Published: November 2026 | By BAOLAN Engineering Team
Most quotations disagree not about the vacuum but about the units: 500 Pa, 5 mbar, 99.5% and "-0.0995 MPa" are all the same setting. This page is a working vacuum level requirements chart for electronic potting applications — every product type listed in both mbar and Pa, with the hold times and the supporting specs that make the number hold in production. Print it, mark your product, and take it to the machine discussion.
Three notes before the chart. First, conversion: 1 mbar = 100 Pa, so a Chinese datasheet at 500 Pa and a European one at 5 mbar are identical. Second, gauges lie below 20 mbar — at 20 mbar the dial already reads 99%, and a spec of "-0.1 MPa" is only 13 mbar absolute. Third, the floor: never set a point below the vapour pressure of water at compound temperature (32 mbar at 25°C, 74 mbar at 40°C), or the vacuum starts working on the compound instead of the cavity. Suzhou Baolan Automation Technology Co., Ltd. uses these exact figures when writing pump-down recipes for customer lines.
1. Vacuum Level Requirements Chart for Electronic Potting Applications
Chamber pressure and hold time by product — all values absolute:
• Potted industrial sensors, unfilled epoxy, 10 mm fill — 30–50 mbar (3,000–5,000 Pa), hold 8–12 min.
• Automotive-grade sensors, filled epoxy, gaps 0.3–1 mm — 5–20 mbar (500–2,000 Pa), hold 15–25 min.
• ECU and control units, 60–75% silica-filled epoxy — 5–15 mbar (500–1,500 Pa), hold 15–25 min.
• Power modules / IGBT, partial-discharge tested — 1–10 mbar (100–1,000 Pa), staged pump-down, hold 20–30 min.
• Ignition coils, filled epoxy, high volume — 5–15 mbar (500–1,500 Pa), hold 10–20 min.
• Transformers and current transformers, HV insulation — 1–5 mbar (100–500 Pa); ultra-high-voltage castings below 10 Pa (0.1 mbar) with dried compound and heated lines.
• Motor stator impregnation, low-viscosity epoxy at 60–80°C — 5–20 mbar (500–2,000 Pa), preheated parts.
• Two-component polyurethane — 30–100 mbar (3,000–10,000 Pa), never below the water floor at compound temperature. Addition-cure silicone — 10–50 mbar (1,000–5,000 Pa), hold 10–15 min.
Two reading rules. The setpoint must be specified at the deepest point of the cavity — a 100 mm column of filled epoxy adds about 15.7 mbar of hydrostatic head, so a 5 mbar chamber is 20.7 mbar at the bottom. And single-digit mbar only pays off when the part has gaps below 0.5 mm, filler above 60%, or a discharge target; on shallow, unfilled work it buys cycle time and volatile loss, not quality.
✅ Bottom line: 30–50 mbar for shallow unfilled work, 5–20 mbar for filled electronics, 1–5 mbar for HV castings — and always read the number at the bottom of the cavity.
2. Vacuum Potting Requirements for Automotive Grade Electronics
Automotive is its own tier not because the vacuum is always deeper, but because the acceptance criteria are written into the drawing. Void criteria typically arrive as customer-specific limits — on the lines we support, commonly total void area under 2% with no single void above 0.5 mm across a creepage path, sampled by X-ray or CT. Partial-discharge targets below 10 pC, with good practice under 5 pC, are what actually force the deep end of the chart: a gas-filled cavity inside HV insulation concentrates the field and discharges long before the resin's dielectric strength is reached.
So, how many mbar vacuum for potting automotive sensors? 5–20 mbar absolute for the filled-epoxy housings that dominate sensor programmes — one to two decades deeper than the 30–50 mbar used for industrial unfilled sensors. The gap between pins, the filler loading and the discharge target set the point, not the badge on the drawing.
The supporting requirements that make the number hold on the line:
• An absolute-pressure sensor below 20 mbar — a compound gauge cannot separate 5 mbar from 20 mbar, and automotive audits will ask which one you ran.
• Staged pump-down with dwells — fast single-step pull-down froths filled compounds and traps more air than it releases.
• A documented pump-down curve per cycle — traceability requirement on most automotive programmes, and the fastest way to catch a leaking seal before it costs a batch.
• A pre-shipment trial on the customer's own adhesive — the setpoint is only real once it is X-rayed on your part.
✅ Bottom line: The vacuum potting requirements for automotive grade electronics are set by the discharge target and the smallest gap — 5–20 mbar covers most sensor programmes, provided the sensor, staging and traceability around it are real.
FAQ
Q: The chart is in mbar — our supplier quotes Pa and "% vacuum". How do I compare?
A: Convert everything to absolute mbar: 1 mbar = 100 Pa, so 500 Pa = 5 mbar and 1,000 Pa = 10 mbar. "% vacuum" is the rest of the trip from atmosphere — 99% equals 10 mbar, 99.5% equals 5 mbar. Anything quoted as negative MPa is a gauge reading: "-0.1 MPa" is 13 mbar absolute, not deep vacuum. A vacuum level requirements chart for electronic potting applications is only comparable when every figure is absolute.
Q: Does automotive grade always mean the deepest vacuum on the chart?
A: No. The tier is set by the discharge target and the gap geometry, not the label — which is why the answer to how many mbar vacuum for potting automotive sensors is a range, 5–20 mbar, not a single number. A shallow, unfilled sensor housing can pass at 30–50 mbar even for an automotive customer, while a filled module with 0.3 mm gaps needs 5–15 mbar. Over-deepening buys volatile stripping and cure defects — the floor is the water vapour pressure at compound temperature.
Q: Can a machine be configured to one row of this chart?
A: Yes. BAOLAN sizes pump, chamber, absolute sensing range and the staged pump-down recipe to the row your product sits in, then verifies it with a trial on your own adhesive and an X-ray of the result. Standard and OEM/ODM builds ship from the factory in Suzhou with a documented pump-down curve as part of acceptance.
Find your row, get it in writing
Send BAOLAN the product type, the compound datasheet and the deepest fill section, and Suzhou Baolan Automation Technology Co., Ltd. returns the chart row as a written setpoint — pressure, hold, pump-down stages — within two working days, free of charge. As a China manufacturer running custom and ODM programmes, we validate every setpoint with a trial on your own adhesive before shipment.
Start with the vacuum potting machine range, or send the product details through the contact page.
www.metermix.cn
Suzhou Baolan Automation Technology Co., Ltd.


